Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

Brembo rebuild kit for Brembo F05 (P5) calipers with 32mm pistons. Contains 2 bolts, all seals and brake grease

This caliper also known as P2 F05N, P32B and P32F.
This seal kit also known as Brembo ref. 120279910, also used on Benelli 504 Sport, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4 (rear).

Not suitable for P32 rear calipers fitted to 750T and Nevada 750 (1991-2001) - see BRA01723 for this model. Will not fit pistons on Grimeca F05 calipers.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 39659000 GU39659000 39 65 90 00
 3965 9000 3965.9000 39.65.90.00

Also fits Benelli 504 Sport, Benelli 250 TS, Ducati Pantah 500SL, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4

Brembo brake master cylinder overhaul kit for overhauling foot operated PS 15 master cylinders on linked systems. Includes all seals and brake grease

This seal kit replaces Guzzi part numbers 17659350, 66139790. Brembo ref. 110273920. This repair kit also used on some Cagiva 650 Elefant models and Benelli Sei. Some Nevada 750 models use BRA14701, check your rear master cylinder before ordering. See this link for help with fitting this kit. Supercedes front kit BRA11043
Note that this kit is only for PS15 models where the piston is retained by a ring, if your master cylinder has a circlip retaining the piston then you have a PS 16 and you will need to replace the whole master cylinder - see BRA19001 for a replacement

 This part is due back in stock soon, call 01484 841395 to reserve yours

 10273920 GU10273920 10 27 39 20
 1027 3920 1027.3920 10.27.39.20

Also fits Benelli Sei, Cagiva Elefant, Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR, Ducati 750 Sport (1972-1974), Laverda Jota

The innovative Stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. Suitable for models with two bleed nipples per caliper

Linked Guzzi brake systems are notoriously tricky to bleed, this M6 auto bleed nipple can save you hours of tedious squeezing and pumping! This bleed nipple is slightly longer than the standard part so some thread will be left showing even when fully closed.

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover

   More than 5 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Brembo brake master cylinder overhaul kit for handlebar, undertank (cable operated) mounted, handlebar mounted and rear PS 12 master cylinders. Contains seals, brake grease, spring and piston. PS12 handlebar master cylinder fitted to early 850 and 1000 models. PS12 rear master cylinder fitted to Nevada 750

This seal kit is also known as 082039797. NB repair kit instructions refer to rear master cylinder. To fit this to a PS12 handlebar mounted cylinder you will need to punch the old piston out using a thin drift through the hole at the banjo bolt end of the master cylinder. Carefully note the order of the ring and washer as the piston comes out and replace with components from kit. Brembo no. 110279720. See this link for help with fitting this kit

 4 in stock

 17659352 GU17659352 17 65 93 52
 1765 9352 1765.9352 17.65.93.52

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei, Laverda Montjuic, Harris F1

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Front right hand brake pipe linking right hand caliper to manifold on front yoke

Original type rubber brakeline with chunky galvanized ends

 This part is available by special order, request a quote

63657121-z 63657121 GU63657121 63 65 71 21
 6365 7121 6365.7121 63.65.71.21

Pair of replacement anodised alloy pistons for Brembo F05 (P5) calipers. These also fit Grimeca calipers with 32mm pistons

Also used on some Laverdas. BRA19301 for alternative part in stainless steel

 This part is due back in stock soon, call 01484 841395 to reserve yours

 19652300 GU19652300 19 65 23 00
 1965 2300 1965.2300 19.65.23.00

Also fits Benelli 250 TS, Ducati Pantah 500SL

Bare aluminium finish brake lever

 1 in stock

17605652-z 17605652 GU17605652 17 60 56 52
 1760 5652 1760.5652 17.60.56.52

Also fits Laverda

Gorgeous polished aluminium reservoir cap for PS15 Brembo master cylinder fitted to rear linked system on many models, will fit front master cylinder on models where a PS15 handlebar master cylinder is fitted. Seal is not included with this cap - you should re-use your original cap seal

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Also fits Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR